bobo99
07-30-2007, 06:40 PM
http://img410.imageshack.us/img410/2366/buffalogg5.jpg (http://imageshack.us)
Raging Buffalo
Beast Fighter
Biography:The Raging Buffalo is strong. With a high endurance, capable of withstanding many blows. Capable of mauling over multiple units at once. It is purely a beast.
Hit Points:50
This unit has a high endurance.
Power:20-15-10 (20-20-20 while Enraged.)
Strong.
Armor:20
It is still a buffalo, it's toughness provides a strong armor.
Blocking:33% Front, 17% Side
While this unit is a tough beast, it is still enraged. Decreasing it's ability to block.
Recovery:2
This unit puts so much brute strength into's it's attacks, it takes a few turns to recover.
Movement:2
A buffalo, large, can not move very well.
Target: http://img253.imageshack.us/img253/6975/attack2zx1.gif (http://imageshack.us)
Ya, I was trying to put do it right, but just got fed up with it and did that :p Ethier way, you should get the point.
It can attack 3 units at once. It mauls the units over, each hit getting weaker, as the buffalo's endurance of worn down (20-15-10, as seen above).
When Enraged this unit does not get worn down, causing 20 damage (reducable by armor) to all three of it's targets.
Additional Infomation:
Does not step aside for friendly units to pass.
Enrage: This unit has the ability to become "Enraged" hence the name, Raging Buffalo. The Rage brings out the brute force of the buffalo, it is caused by anger. You anger the Raging Buffalo by burning it from a Pyro, DSM, Dragon or Lightning Ward, freezing it via the Frost Golem, or poisening it via the Wisp. The Raging Buffalo can only be Enraged once, after that it goes back to it's normal power. Rage lasts 2 Turns.
Pros:
*High Hp
*High Armor
*Ability to attack 3 units at once
*High Damage output
*Enrage
Cons:
*Low movement
*Low blocking
*High recovery
*Does not step aside for friendly units to pass
Feedback please.
Raging Buffalo
Beast Fighter
Biography:The Raging Buffalo is strong. With a high endurance, capable of withstanding many blows. Capable of mauling over multiple units at once. It is purely a beast.
Hit Points:50
This unit has a high endurance.
Power:20-15-10 (20-20-20 while Enraged.)
Strong.
Armor:20
It is still a buffalo, it's toughness provides a strong armor.
Blocking:33% Front, 17% Side
While this unit is a tough beast, it is still enraged. Decreasing it's ability to block.
Recovery:2
This unit puts so much brute strength into's it's attacks, it takes a few turns to recover.
Movement:2
A buffalo, large, can not move very well.
Target: http://img253.imageshack.us/img253/6975/attack2zx1.gif (http://imageshack.us)
Ya, I was trying to put do it right, but just got fed up with it and did that :p Ethier way, you should get the point.
It can attack 3 units at once. It mauls the units over, each hit getting weaker, as the buffalo's endurance of worn down (20-15-10, as seen above).
When Enraged this unit does not get worn down, causing 20 damage (reducable by armor) to all three of it's targets.
Additional Infomation:
Does not step aside for friendly units to pass.
Enrage: This unit has the ability to become "Enraged" hence the name, Raging Buffalo. The Rage brings out the brute force of the buffalo, it is caused by anger. You anger the Raging Buffalo by burning it from a Pyro, DSM, Dragon or Lightning Ward, freezing it via the Frost Golem, or poisening it via the Wisp. The Raging Buffalo can only be Enraged once, after that it goes back to it's normal power. Rage lasts 2 Turns.
Pros:
*High Hp
*High Armor
*Ability to attack 3 units at once
*High Damage output
*Enrage
Cons:
*Low movement
*Low blocking
*High recovery
*Does not step aside for friendly units to pass
Feedback please.